Rust-Oleum Painter's Touch 2X Ultra Cover Gloss Spray Paint - 12 oz

Rust-Oleum Painter’s Touch 2X Ultra Cover contains technology that provides twice the coverage on wood, metal, most plastic, wicker and more when compared to other matching colors of Rust-Oleum general purpose paints: Painter’s Touch, Spray N go, Quick Color and Touch ‘n tone. It covers surfaces with fewer spray passes, allowing projects to be completed faster and easier. Any angle spray feature allows you to spray in any direction, even upside down. Fast Drying.

• Premium general purpose spray paint
• Ultimate coverage
• Apply to a variety of surfaces - wood, plastic, metal and more
• Any-angle spray system allows you to cover those hard to reach areas
• Comfort spray tip helps eliminate finger fatigue while completing larger projects
• Fast drying

Remove all dirt, grease, oil, salt and chemical contaminants using a commercial detergent or other suitable method. Rinse with fresh water and allow to dry thoroughly. Remove loose paint and rust with a wire brush or sandpaper. Previously coated surfaces must be sound and in good condition. Smooth, hard or glossy finishes should be sanded to create a surface profile.

Use of Painter’s Touch 2X Ultra Cover primer provides superior adhesion and hiding and is especially recommended for bare wood and metal.

Use outdoors or in a well-ventilated area such as an open garage. Use when temperature is between 50ºF-90ºF (10ºC-32ºC) and humidity is below 65% to ensure proper drying. Do not use on objects that may exceed 200ºF (93ºC) surface temperature. Do not apply to galvanized steel. Avoid spraying in very windy and dusty conditions. Cover surrounding area to protect from spray mist.

Shake can vigorously for one min after mixing ball begins to rattle. If mixing ball fails to rattle, o not Strike Can. Contact Rust-Oleum. Shake often during use. Hold can upright 10-16" from surface and spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can the same distance from the surface and in motion while spraying. Apply 2 or more light coats a few mins apart to avoid drips and runs. Do not use near open flame.

Dry and recoat times are based on 70ºF and 50% relative humidity. Allow more time at cooler temperatures. Dries to touch in 20 mins, to handle in 1 hr and is fully dry in 24 hr. Apply a second coat or clear coat within 1 hr or after 48 hr. Apply clear in 2-3 light coats a few mins apart.

Note: On plastic, maximum paint adhesion and durability is achieved in 5-7 days.

When finished spraying, wipe off tip before storing. Clean up wet paint with xylene or mineral spirits. Properly discard empty container. Do not burn or place in home trash compactor.

If valve clogs, twist and pull off spray tip and rinse it in a solvent such as mineral spirits. Do not stick a pin or other object into the stem.

• Resin Type: Acrylic Modified Alkyd, Alkyd
• Solvents: Acetone, n-Butyl Acetate, Naptha, Xylene
• MIR Max: 0.95
• Fill Weight: 12 oz
• Recommended Dry Film Thickness (DFT) per Coat: 1.0-2.0 mils (25-50µ)
• Practical Coverage at Recommended DFT (assume 15% material loss): 8-12 sq. ft./can (0.74-1.11 m²/can)
• Dry Times at 70°F (21ºC) and 50% Relative Humidity - Touch: 20 mins
• Dry Times at 70°F (21ºC) and 50% Relative Humidity - Handle: 1 hr
• Dry Times at 70°F (21ºC) and 50% Relative Humidity - Recoat: Within 1 hr or after 48 hr
• Dry Heat Resistance: 200°F (93°C)
• Shelf Life: 5 Years
• Flash Point: -156°F (-104°C)

Some plastics made of polyethylene, such as plastic storage containers, are manufactured in a way that may hinder maximum paint adhesion. Test paint in a hidden area first.

If you scrape, sand or remove old paint, you may release lead paint dust. Lead is toxic. Exposure to lead dust can cause serious illness, such as brain damage-especially in children. Pregnant women should also avoid exposure. Wear a NIOSH-approved respirator. Clean up carefully with a HEPA vacuum and a wet mop.